Author Topic: [ARM/Nspire] Drawing sprites (Read 5231 times)

ElementCoder · « **on:** February 01, 2014, 01:29:30 pm »

So I have the following piece of code which draws a sprite on the screen:

#include <os.h>
main: .global main
	push {r4-r11, lr}
	bl lcd_ingray
	bl clrscr
	ldr r0, =0xC0000010
	ldr r0, [r0]
	mov r2, #8
	adr r1, sprite
	add r0, #200				@ x
	add r0, #SCREEN_WIDTH/2 * 80		@ y
draw:
	ldr r3, [r1], #4
	str r3, [r0]
	add r0, #SCREEN_WIDTH/2
	subs r2, #1
	bne draw							@ if there are lines left, draw the next one
	bl wait_key_pressed
	mov r0, #0
	pop {r4-r11, pc}
	
sprite: .word 0x00000000, 0x00000000, 0x00FFFF00, 0x00FFFF00, 0x00FFFF00, 0x00FFFF00, 0x00000000, 0x00000000

This is probably a stupid question, but the problem I'm facing is that I can only use x coordinates that are a multiple of 4. What would I need to do to be able to use any number for the x coordinate?

Legimet · « **Reply #1 on:** February 01, 2014, 06:53:27 pm »

I dont know ARM asm, but each pixel is a short int in the 16-bit high color format.

Matrefeytontias · « **Reply #2 on:** February 01, 2014, 07:13:07 pm »

Nope.

Code: [Select]

bl lcd_ingrayEach pixel is 4 bits long. I also don't ARM ASM though.

Vogtinator · « **Reply #3 on:** February 01, 2014, 07:42:16 pm »

Jup, each pixel is 4 bits, so half a byte. You can either:
-store the half byte in a separate register
-switch to 8bit mode
-use a separate method for reading and writing pixels given x and y
-use c and don't think about the low level stuff

fb39ca4 · « **Reply #4 on:** February 01, 2014, 10:42:25 pm »

You should switch to writing bytes, not words, and then since pixels are 4 bits, have two different routines, one byte aligned and the other not which you choose when the x coordinate is even or odd respectively. Alternatively, if you need this to be really fast, you can set the LCD controller to 8 bits per pixel.

chickendude · « **Reply #5 on:** February 16, 2014, 02:23:17 am »

I would also recommend using bytes.

Otherwise, how would you do that in z80? Why not try shifting the word you're trying to draw? Shift right to draw the left side of the sprite, shift left to draw the right side. For example, if you want to draw at SCREEN_ADR+1, you would store r3 shifted to the right one byte (8 pixels) to SCREEN_ADR+0, then r3 shifted to the left (4-1)*8 = 24 pixels to SCREEN_ADR+4. In ARM you get free (immediate) shifts with most commands, or you can load the offset into a register and use LSR or LSL to shift (or ROR to rotate). Register shifts are slightly slower (1 cycle), but still!

DJ Omnimaga · « **Reply #6 on:** February 16, 2014, 02:30:49 pm »

Quote from: fb39ca4 on February 01, 2014, 10:42:25 pm

You should switch to writing bytes, not words, and then since pixels are 4 bits, have two different routines, one byte aligned and the other not which you choose when the x coordinate is even or odd respectively. Alternatively, if you need this to be really fast, you can set the LCD controller to 8 bits per pixel.

What I don't get is how a 4 bit pixel can use 65536 different colors on CX models

chickendude · « **Reply #7 on:** February 17, 2014, 03:48:49 am »

"bl lcd_ingray" sets it in grayscale mode, that's how

Vogtinator · « **Reply #8 on:** February 17, 2014, 11:16:08 am »

Quote

What I don't get is how a 4 bit pixel can use 65536 different colors on CX models

On the CX, each pixel is 16 bit (RGB 565)

Author Topic: [ARM/Nspire] Drawing sprites (Read 5231 times)

ElementCoder

[ARM/Nspire] Drawing sprites

Legimet

Re: [ARM/Nspire] Drawing sprites

Matrefeytontias

Re: [ARM/Nspire] Drawing sprites

Vogtinator

Re: [ARM/Nspire] Drawing sprites

fb39ca4

Re: [ARM/Nspire] Drawing sprites

chickendude

Re: [ARM/Nspire] Drawing sprites

DJ Omnimaga

Re: Re: Re: [ARM/Nspire] Drawing sprites

chickendude

Re: [ARM/Nspire] Drawing sprites

Vogtinator

Re: [ARM/Nspire] Drawing sprites