0 Members and 2 Guests are viewing this topic.
Quote from: stefos on December 17, 2013, 05:49:59 pmQuote from: ipwn3r456 on December 16, 2013, 01:08:10 amWow. It's been 4 months already and I haven't done anything... OS 3.6 is here for Ti-Nspire series. Is there any new ways for installing Ti-Nspire CX CAS into a Ti-Nspire CX now? Would it work if I put OS 3.6?Hey man,I downloaded the 3.6 OS & you can run Ndless but only under the Boot 2 (There are 2 boots to go under btw)and you have to install 3.1 OS as well under Boot 2.There is some hardware you have to buy & hook up & then you have to reset to run Ndless.I don't know what you're talking about the way you said it. If someone reads this without knowing everything he might get confused and try to install OS 3.6 first the official way which is a doomed way.The correct facts are : You can run OS 3.6 with nLaunchy and if you want you can run Ndlessed OS 3.1 with nLaunchy switch feature (see the many Ndless switch topics).In order to have nLaunchy available you have to have boot2 3.1. This is where the hardware part comes. If you don't have boot2 3.1 you may use a TTL/USB adaptator to reprogram this boot2.But this is not the end. If you have an Nspire with >= J-revision, you have to buy a new mother board from a reseller.So next time, don't say you can install Ndless and OS 3.6, these are two seperates things (see Ndless switcher 3.6).
Quote from: ipwn3r456 on December 16, 2013, 01:08:10 amWow. It's been 4 months already and I haven't done anything... OS 3.6 is here for Ti-Nspire series. Is there any new ways for installing Ti-Nspire CX CAS into a Ti-Nspire CX now? Would it work if I put OS 3.6?Hey man,I downloaded the 3.6 OS & you can run Ndless but only under the Boot 2 (There are 2 boots to go under btw)and you have to install 3.1 OS as well under Boot 2.There is some hardware you have to buy & hook up & then you have to reset to run Ndless.
Wow. It's been 4 months already and I haven't done anything... OS 3.6 is here for Ti-Nspire series. Is there any new ways for installing Ti-Nspire CX CAS into a Ti-Nspire CX now? Would it work if I put OS 3.6?
I didn't get more technical because I wanted him to do the spade work & read what I posted.
I jumped the gun without asking here & installed 3.6 My hardware is an "E" model which has Boot 1 & Boot 2.
P.S. Levak...In the future, try asking people what they mean before accusing.....Not good manners.Adieu
Note: if you don't like Levak's way of speaking, it's best to just ignore him or better, only take the useful info from his posts, and if you really feel he has been out of line, then there's a thumbs down icon right above his post and a report to moderator link at the bottom. A 404 not found will occur when sending a report but it will send and mods will get notified.I think he was fine, though, although we need to understand that each other's native language isn't English. Your post, from my point of view, could have misled people into installing OS 3.6 the normal way, thinking it runs Ndless, especially if people don't bother reading all the post. As for Levak, his posts often sounds more rude than he normally is, he's definitively no troll and while we prefer that people remain as courteous as possible, he definitively has no intention to single you out as forum user. Installing OS 3.6 is very, very dangerous from an Ndless point of view, so he's just trying to save people from installing it by mistake.By the way, "Adieu" in French means "so long" or "farewell" over here.
I downloaded the 3.6 OS & you can run Ndless but only under the Boot 2 (There are 2 boots to go under btw)