This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Lipe_oa
Pages: [1]
1
« on: November 13, 2014, 10:49:20 am »
I have a problem with my update on the status of the battery , it happens after I reflash my Boot2 v3.2.4.7.
Now changes the status 25% in 25 % and if I press the reset button.
Can I fix this?
2
« on: November 10, 2014, 10:39:17 am »
solved , I put Boot2 v3.2.4.7 and returned to run OS 3.6.0.550 . thanks to those who helped .
3
« on: November 10, 2014, 07:57:08 am »
Yes, you need to. Ok. thanks for that part.
Connect GND to the longer pin on the left side and RX of your adapter to the left pin next to it.
Still didn't happened nothing on hyperterminal, is the conversor. I already asked other for the seller. When arrive the new I try again.
Q) When I put the Boot2 V3.1 I need reinstal the OS? Or I just Turn on the calculator?
4
« on: November 09, 2014, 06:10:07 pm »
Yeah, either you're using the wrong pins or your adapter is fried. I'm think the adapter isn't working, because I tryied in 3, 4 and 5 conectors in left and right side.
No, your calc doesn't support nlaunch. So I need put de Boot2 V3.1 to the calculator work again?
Well, Pin 1 is Pin 1. The serial pins are on the left side if the calculator is facing downwards and the port points to you.
Look my calculator:
 What do you think? thanks again! so much!
5
« on: November 09, 2014, 04:06:53 pm »
It was rejected, I assume. Did you do anything with nsNandMgr? No, I just did the Tuto. What do you mean by "didn't connect"? After you open the serial port nothing happens?Try to connect GND and RX only.
When I try to connect with the hyperterminal show me that i'm connected but don't show me nothing in the screen, like this:
http://screenshots.en.sftcdn.net/en/scrn/10000/10028/hyperterminal-private-edition-htpe-1.jpg
And I already tryied to connect with RX and GND, nothing happens.
After you got your calc in a usable state, do a normal installation of the 3.6 CX OS.
So I can't put OS's with CAS anyway?
One more doubt, my Ti has the number 1 in the right side, it's normal or I need to invert my connections?
Thanks man!
6
« on: November 09, 2014, 02:25:00 pm »
First, thanks for your Help! How? What did you do? I tryied this: http://www.omnimaga.org/general-calculator-help/installing-cas-on-ti-nspire-cx-non-cas/msg383792/#msg383792and don't change de hole name, the extesion .tcc to .tns, just de first name. Try to connect only the RX and GND pins first.With 115200 Baud you should get at least some traffic from boot1.
Didn't connect, neither in RX or TX!
My conversor can be broke? when I connect TxD, RxD and GND don't light the yellow light, just de Blue and Red, the yellow becomes weak!
No, won't work. v1.4 is for touch and clickpad only.
What I do?
8
« on: November 05, 2014, 08:39:33 am »
How to downgrade Ti-Nspire CX 3.6 (Non CAS) to 3.2 CAS O.S
Current:
- Ti-Nspire CX 3.6 (non CAS)
Now, You want to downgrade Ti-Nspire CX CAS 3.2. Ok!
Step 1: Download [ nLaunchy 3.2/3.6 switching pack ]
Link: http://tiplanet.org/forum/viewtopic.php?f=57&t=13213
Extract: NL_3.2-3.6_switchpack\TI-Nspire CX\ndless
- Send : the [ndless] folder =>>> Ti Calculator
- On Ti Calc / Open [ My Documents ] //// you see [ndless] folder. pess Enter 'ndless_installer' and then [ Y ]
After that, press [ 2] and [ 2 ] ....and [ 0 ] to complete installation.
Exit
Step 2: Download ROM 3.2 Ti-Nspire CX CAS
- Run file: TNOC_en.exe Link download: http://tiplanet.org/forum/archives_voir.php?id=1922&short=1
check Delete boot2
- Rename new file: TI-NspireCXCAS-3.2.3.1233_b.tcc to [ phoenix.tns ]- Copy file: phoenix.tns to [ NL_3.2-3.6_switchpack\TI-Nspire CX\non-CAS\nlaunch ] on PC.......overwrite
- Copy [ nlaunch ] folder in [ NL_3.2-3.6_switchpack\TI-Nspire CX\non-CAS\nlaunch ] to Ti Calculator
- Press [ Reset ] button back: Operating system not found. Install now.
- Connect and copy file: nlaunch.tco in ( NL_3.2-3.6_switchpack\TI-Nspire CX ) on PC. It will reboot
Waiting and using
Note:
If there're troubles. You should do:
1. Press and Hold (4 keys): Doc + Enter + Ee and Release [Reset] Button
[ 2 ] and [ 1 ] ....and then [Enter]
You can install new OS
2. With fail belong to NSC MP V4 Diag. You can do:
Press and Hold (4keys): Esc + Menu+-and Release [Reset] Button to disable diag test
3. Everything...You can do:
Release [ Battery rechagreable ] about 3 - 5 second to clear fail
Thanks!
I'm from Vietnam. So i don't write Ennglish well. Sorry!
You can send my Email: [email protected]
I try this but in " - Rename new file: TI-NspireCXCAS-3.2.3.1233_b.tcc to [ phoenix.tns ]" I don't rename the extesion so my Ti CX non CAS with OS 3.6 restar and stop in "System Error" screen.
I already try to format, delete system operator but don't heppened anything (sorry for my english, I'm brazilian)
Pages: [1]
|
Show Posts